Sunday, May 3, 2026

Octopus grips!

 I have had a consistent niggle since I bought the bike. The bike has heated grips and over time they have become smooth with the heat and wear. The smoothness means I have to grip very tightly in order to manage the throttle which, as you probably know, is a twist grip on the right handlebar. It gets tiring on a long ride and makes my my right arm stiff which is not helpful when manoeuvring or steering the bike. 

I have tried a few fixes: Gloves with rough palms, wrapping cloth electrical and push bike handlebar tape. The gloves were just had not the required purchase. The cloth tape was a bit too good as I could not let go of the throttle quickly enough whilst riding and the push bike handlebar tape was just the right amount of tacky but lost its tackiness after a couple of outings.

 I accidentally bumped into @moustachmoto on YouTube shorts. He had the same problem as me, slippy heated grip. His solution was cricket bat grips. Watch the video to see how its done. It worked a treat.  

   

 https://www.youtube.com/shorts/4I5VySPLXPE

I found cricket bat grips at my local Sports shop. They were on offer too. Just £2.50. One packet was enough to do both hand grips with some left over. The shop only had Octopus type. These slips are textured for extra grip. 

  

  

The picture is of the right hand side grip, the throttle, which I had been riding with for years. I followed @moustachemoto  instructions and it worked a treat. 


The only extra thing I did different to the video instructions was to remove the bar end weights. It is a quick job with an Allen key. It really was an easy job. Once finished I tested the grips. One hardly has to apply any grip pressure to twist the throttle open. 
 
 
A cheap and quick solution. I wish I knew about it earlier!
 



Thursday, December 30, 2021

Side lights replacement

   A few weeks ago I noticed one of my LED side lights was not working. It got the usual jiggling and a tapping but it would not be fixed. These LEDs came with the head light upgrade in 2020. Click HERE to read the post about the head lights upgrade. 
 
 
I bought a new set off Amazon. I figured I better replace both lamps since the likelihood of both lamps matching would be slim. Monies paid and delivery arrived in quick time. I then had to wait for a time to do the replacement job.

The lamp on the left is the one I am replacing. The one on the right is what was delivered. 

 

 

   The near-side lamp was easily replaced by simply reaching past the headstock, inserting the new LED into the lamp holder. I had the lamp holder out to check the bulb so I could order the correct fitting. I flicked on the light switch to check the lamp was working then wriggled it back into the lamp housing. The off-side lamp was not nearly so easy.

 

    I started with reaching past the headstock into the bowels of the fairing, as I had done with the other side. I should have realised I was being led into a false sense of security with the ease of the replacement on the near-side. I could not locate or even reach the back of the near-side lamp housing much less pull out the lamp holder. I removed the binnacle area of the fairing. Ten screws and numerous panel poppers later the dashboard was out of the way giving a little more access. it took a bit of yoga like positions to finally see the back of the lamp holder. Once I got my fingers on the rubber lamp holder it took a fair bit of tugging and wiggling to work the lamp holder free of the lamp housing. Swapping the old bulb for the new ones took seconds. The light switch was flicked and the lamp came on. The it was a case of refitting the panels with the screws and poppers then retest the light switch. Yup the light still work. It is not always the case. Fitting the lamp holder into the holder sometimes dislodges the bulb and it fails to illuminate. It worth a quick test before the bike is put away. 

 


   

 

   The side lights are now the same colour as the day riding lights on the mirror pods. The previous LEDs had a blue tinge to them and were not quite so bright. 


So that is another upgrade for a hours work.

Sunday, September 26, 2021

All to save a pound (£)

I have been following a YouTuber called Itchy boots Click HERE for Noraly's website She journeys around the world, buying a bike then travelling around. She has an interesting point of view on travelling alone. Anyhoo that is not the point of this post.

Noraly is bound to get a puncture at some point as all travellers rolling on pneumatic tyres but she is prepared, whereas I am not....until now, well nearly.

I bought a mini air compressor from Rocky Creek Designs  based on Noraly's experiences. It fits under the tail unit in a nifty bag. The compressor came with a couple of different electrical connectors. Circular tags for permanent electrical connection and crocodile clips for hooking up to any battery. 

When I did my big refurbishment of the Pan I added a distribution board with the idea of having the flexibility to permanently connect auxiliary equipment. Today it paid off.   

 


 

 

 

So all I had to do was route the cable. Unscrew a terminal, then screw done the terminal with the coloured coded ring connector, which was already attached to the wire. Do it again for the black (negative) wire. Fit the recommended 15 amp fuse... Done! 

 

 Then a test. Plug the electrical connector together and flick the "on/off" switch on the unit. It makes a noise and covering the air connector with my thumb I could feel the air being pumped. Job done. 

 

The cover for the fuses was fitted and the distribution board tucked back into its place in the tail unit. The The compressor went back in its bag and that too was stowed under the tail unit. 

 The last part of being puncture prepared is to buy a repair set. They usually come with rubber bung, glue and tool. I have air. 

 

Also no need to pay a pound (sterling) or more the blow up tyres at the petrol station. Double result.  


Sunday, May 9, 2021

Scrubbing in new tyres

   The weather was dry and it was a Sunday so it seemed like an opportunity to take the bike for a spin and scrub in the new tyres. I set the tyres pressure to the recommended values 32psi front and 42 psi in the rear. With no data to go from I figure I would start with the recommended pressures. The road were were dry, the air temperature about 17c but with a strong cold wind. I set off with no objective but the ride a few miles taking in some motorway, sweeping A roads and twisty and B roads.


   I ran up the road to the next village, Woodville for petrol. From there I pointed the bike in the general direction of Derby. I took the A514 which took me across the ancient monument that is the Swarkstone causeway. The first mention of a bridge across the River Trent at Swarkstone is in 1207. I suspect it was a route north and a ford back into antiquity.  Fast forward to 1745, Bonny Prince Charlie and his Jacobite army gave up their march at Swarkstone. Perhaps the beer and vitals at Harper & Crewe pub, hard by the bridge, did not suit them. From there to the A50. I took the link road from the A50 round the M1 to the A453 to Nottingham. 

   I have this new app on my phone called "Relive" which tracks your ride. You can add pictures as you go and at the end create a flyover of your route. See the link at the bottom of this post. So first stop Ratcliffe power station.

 

Pan by Ratcliffe power station

  Right at the foot of the cooling towers is East Midlands Parkway train station on the east coast mainline. Its an edge lands with the river Soar and the canal and a marina all close by but there is still lots a open space....for now.

   When they where designing Ratcliffe they arrange the cooling towers so that from the highest point near Leicester at Bradgate Park (The birth place and home of the Lady Jane grey, the nine day queen usurped and judicially murdered by Mary Queen of Scots), which is 15 miles to the south, the viewer would only see two towers as the other towers where aligned to be behind each other. A nice piece view preservation. 

   From the station I rode into Nottingham and tried to get near to Nottingham castle. No luck. I them struck out north along the A60 towards Mansfield. A little after Arnold I took the A614 towards Doncaster but then turned east onto the B6386 in direct of Oxton. before Oxton I turn south east and took in the villages of Calverton, Epperstone and Hoveringham. Just after Hoveringham the River Trent sent me back to the A6097 via Caythorpe. A short scoot along the A6097 then a short blast up the A46, the old Roman road, The Fosse way to Lincoln. I turned off for un-numbered roads to Scarrington then on to Whatton, Sutton, Red Mile on to Belvoir castle poking up, on the ridge, above the trees. From there to a break at Denton. There was some great open spaces out there and pretty hamlets.

   After a short break in the picturesque hamlet of Denton (check it out in the video) more back roads trending south to Sproxton, Coston, Garthorpe and on to Melton Mowbray. From there it is the well worn A6006 through  Asfordby, Wymeswold, Rempstone and Hathern back to Ashby de la Zouch. The A6006 is a really good road for bikes, fast flowing sweeping bands and some twisty bits connect by long straights.

Miles run 118.  

https://www.relive.cc/view/vZqNn4g7QGq


Saturday, May 8, 2021

Tyres

   Since your tyres are the only things touching the road they are quite important. Tyres have a lot to do. Having a decent amount of tread is obvious. It is a legal requirement and its quite handy for clearing water when riding in the wet. The tyre tread also provides grip which is kind of handy for cornering and braking. The carcass (body) is worked hard as the tyres flex under loads from acceleration, braking and cornering. Then there is the weight of the bike simply resting on the tyres.  

   It is fairly obvious that when the tyre wears the rubber that make contact with the road worn away which is seen as the tread pattern disappearing.  The carcass (body) of the tyres also ages from constant deformation under loads, heat and cold.

   All these micro factors build up the slowly to affect the handling of the bike. Being humans we adapt but legal requirement aside, there is a point where the tyres need replacing. 

Rear GT4 

My old rear tyre has been squared off. This happens because the bike spends most of its time up right. It also wear off the tread on the centre of the tyre which not helpful in the wet.

 

 It affects the handling. The bike tracks easily in a straight line but when you need to bank to turn the tyre has to roll over the edge of the squared off section. More about this later. 

 

 

 

   The front tyres has a different problem. Again the maximum wear is on the centre line. Its not squared off because the most of the weight of the bike and all the power goes through the back tyre. The front tyre has to deal with side grip for turning and 90% of the braking forces. If you look closely at the horizontal tread grooves you will see it is scalloped from the deformation of the carcass under braking.

   Both tyres are no longer true to their manufactured  shapes. The carcass of both tyres are not as robust as they once where. In banking to turn the shape issue provides a conflict in the arc tyres describe on the road and side ways roll of the tyre from upright to lean and back again. As the side wall of the tyre degrades it no longer supports the bike in the turn and starts the move about. That might cause the tyre to slide sideways in the corner. The back tyre might loose grip a skid and hopefully regrip or cause the front to tuck. 

  What is not often recognised is that when the tyres deform under load (braking or accelerating) it changes the geometry of the bike to a greater extent than the that which is expected under that load and that affects the handling of the bike.

   Then comes the research to find the "best tyres". But what is your focus? Stickiness for maximum corner speed, acceleration and braking or maybe longevity for commuting, good performance in the wet. Probably a combination of the all. The decision is perhaps made easier when there are only a few fitment options.  

   The choice for the Pan is pretty simple, Michelin Road GT5. The GT5 is the go to tyre and it so happens the tyre shop had them in stock. I decided I would take the wheel off he bike  rather than take the while bike to the shop and be charged to remove ad refit them. Also I could check over the brakes and under side of the bike.

   I put thebike up on the lift. The back wheel comes off first. Its a bit of a faff because you have to remove the number plate and mudguard and swing the off side silencer out of the way otherwise the axle will not come out fully. The brake caliper has to be undone and swung out of the way. Only then can the wheel can be pushed of the splines and rolled out, jiggling the caliper out the way of the wheel rim. 

   I put a scissor jack under the front of the engine to lift the front wheel. It goes a light higher when the back wheel is out. Undo two pinch bolt at the bottom of leg fork leg. Remove two bolts that hold the brake calipers on. Remove the 22mm axle bolt. The wheel won't roll out of the bike because it catches on the mudguard. Taking the front mudguard is a proper faff. Luckily the bike lift has a removable floor panel. With the panel removed the axle pin can be removed and the wheel lowered through the floor panel.

  Then a spin down to Wheel House Tyres to have the booked set of GT5s fitted.  It was the first time I used Wheel House Tyres. It was a very professional set up. A new set of tyres fitted and balances in twenty minutes. Check them out at https://www.wheelhousetyres.co.uk/

 

   Refitting the wheel is the reverse of removing them. If you push the brake pads back in the calipers it makes jiggling the caliper around the brake discs not quite so awkward. 

Things to remember:

The profile of the tyres is different to the old ones. Handling will be very different.

The surface of the tyres have a release agent to help remove them from the mould in the manufacture process. It takes some miles to wear off the agent so the grip of the tyres is compromised. 

Go steady!  


 

Sunday, April 11, 2021

Charger leads

 I have a a splendid charger from Optimate. They come with a plug and lead that you can attach to your bike's battery. When you need a charge you plug the charger into the bike. However I have two bikes that need charging but only one lead. No probs, look up the Optimate website, find my charger model and order a lead....er no....discontinued. I did not fancy forking out ninety quid for a replacement charger with multiple leads in the new format. 

 

 

  So easy enough. Make up a news leads with compatible plugs. I had a tray of suitable plugs from the other wiring jobs. The Pan had a lead but with the obsolete plug style. I did not replace the side panels when I replaced the battery as the problem was evident as soon as I put the battery on to charge.

 

    I could swap out the obsolete plug whilst is was attached the a live battery. SO the lead was take of the bike. It also made the job easier. I decide the male plug would go on the charger and female plugs on the bike.

 

    To make sure I did not cock up I started with the male plug on the charger lead. The charger lead was very long so I was able to cut off a length to make the bike side lead for the Yamaha.  I had a good deal of practice making plugs when I did the wiring on the Pan for the power sockets so it was just a case of working through the process. The key thing was to make sure the polarity was correct, especially as all the wires were black. 

   The lead for the Yamaha needed terminal rings as well. As luck would have it there were just two in a electrical bits a bobs box. A bit a shrink wrap to tidy up the ends and the that part of the job was done.

The last part was to attach the leads to the batteries on each bike and test the charger. If the polarity was wrong the charger would not work. As it was the charger indicator lights lit up as they are supposed to. Now I can plug the charger into either bike as required.      

Saturday, April 10, 2021

Dead Battery

   I made a bit of a mistake and and left the accessories switch in the "on" position after a ride. When I decided I wanted to go for a spin I did the usual checks a few days before only to find the battery was flat. I realised at that point what I had done. No probs.....just plug in the battery charger and check back in the morning. checking back the next day showed the battery had not recovered or the next day. So the battery was goosed. It was less than two years old. The battery on bikes have never been that powerful so it does not take too much to kill them.

   Nothing else for it but to buy a new one. Everything is on-line so a quick search on the PanEuropean Facebook group turned up a likely supplier. Half an hour later two batteries were on their way from Sportsbikeshop.co.uk.  I figured since the Yamaha battery was flat too, It is 20 years old, I would order one for that too and save on the postage. Two batteries got me free postage so a good win.       


  

 Given that one battery is for a sports bike and the other is for a touring bike there is not much difference in the size or power output. That probably under lies the Pans feeble battery stamina.  



   Fitting the battery is a bit of a faff, mainly because most work on the Pan starts with removing panels. In this case, seats come off and the off-side side panels. There is a second cover the for the battery and retaining strap. Only then can you undo the terminal connectors. The old battery is jigged out the new one jiggled in and everything returned to it usual place. I dabbed a little Vaseline on the battery terminals to prevent corrosion. I have been doing this since I start fettle cars with my Dad.

   Having fitted a new battery and checked the voltage, I figured it needed an overnight charge to bring it up to full power. I was right and next day the bike started up without an issue.   

   However a little wrinkle raised it head. Two batteries and one charger. Subject of another post.